Your Reviewer
My Credentials
So who's doing this reviewing then?

Well I've been building and flying or driving radio controlled models for over 40 years and during that time I like to think I've built up a reasonable amount of knowledge.
I'm also a qualified electronics engineer who has worked in radio frequency, analog, digital systems and software for more than three decades. In fact I designed and built my first RC set back in 1969.
For the past nine years I've also been involved in the design and manufacture of some rather sophisticated engine technology and UAV flight control systems.
So, chances are I've been there, done that and have a huge pile of tee shirts to prove it.
Right now I'm heavily into 3D flying and enjoy all aspects of the RC hobby. I may be old but I don't feel it.
In the Pipeline
Here's just a little bit of what's to come on this site...
RC explained: Demystifying terms such as PCM, PPM dual conversion, single conversion, full-range etc., this feature will explain it all.
Cheap Chinese Engines: Just how good are those cheap Chinese glow and gas engines that sell for half the price of their "brand-name" equivalent? I put several to the test.
Build your own radio gear?: Back in the old days, building your own RC gear was not uncommon and now the arrival of 2.4GHz has made it practical again.
DIY: The RCModelReviews FPV Backpack
AN EASY TO BUILD AND USE AIRBORNE FPV SYSTEM

Dated: 25 May 2012
By now most readers will have seen the RCModelReviews FPV backpack in action and many of you have expressed an interest in building one for yourselves.
Well here is where that information will be published.
What does it do?
The FPV backpack is a simple device that contains a 200mW 5.8GHz video transmitter, a 5V UBEC, a voltage regulators, a voltage dropper/filter for popular 9V-12V cameras, a low-cost board-camera and an optional microphone.
In its cheapest form, this will probably cost you little more than $50 to build but if you want best results, I highly recommend investing an a decent board-camera -- which will likely bring the price closer to $80 or $90 - but the results will be stunning!
By building all this functionality into a single unit that can be attached to virtually any model by a strip of velcro, it becomes cost-effective to fly a whole bunch of different RC planes (or boats or cars) using FPV.
The system is designed to work from a 3S lipo, usually the same lipo that powers your ESC and motor but in the case of a larger model that might have an IC engine or a 4-6S lipo, a small separate 3S pack can be used.
What you'll need
The heart of the system is the tiny 200mW 5.8GHz video sender modules which can be purchased online from a number of sources. The price of these modules varies from US$15 to US$20, depending on your source.
It is this module that converts the video and sound signals into a radio-frequency transmission that is received on the ground and used to send the video to your FPV glasses, visor or screen.
Although these modules claim to be 200mW, I'm not so sure they're actually that powerful but right now I don't have any equipment to confirm that suspicion (test gear for working with 5.8GHz signals is very expensive). Never the less, these modules work very well for the kind of short/medium-range FPV for which this system is designed.
These modules require 3.3V of power -- any more and the magic smoke will come out -- any less and the range will be considerably reduced. For that reason, the backpack has a 3.3V regulator on its circuit-board that ensures the modules are properly fed and watered (so to speak).
While this regulator could have been designed to accept the full 11.1V of a 3S lipo, that would have meant making it bigger, heavier and wasting more of your battery's power as heat. For that reason, a cheap 3-5A SBEC is used to drop the full battery voltage down to 5V before it goes into the 3V regulator on the backpack. A simple solution to an otherwise complex problem.
The circuit board also contains a second regulator, this one delivers a safe and constant 9V for the camera. By using this regulator, the problem of interference from the ESC is eliminated, where the backpack is powered by the main flight battery. It also means that the camera tends to run a little cooler -- which is a good thing.
Of course no FPV system is complete without an antenna and the RCModelReviews FPV backpack
uses the popular clover-leaf, circularly polarized antennas developed by a gentleman
calling himself IBCrazy. These are super-cheap to make and work much better than the
traditional black plastic-covered dipoles that ship with most commercial FPV systems.
And, of course, you'll need a camera. See the RCModelReviews YouTube channel for the reviews of several cameras and decide for yourself whether you'll be able to get away with a cheap "under $20" camera, or whether it's worth spending an extra $30 for the "top of the line" high-resolution CCD camera with "wide dynamic range".
Finally, there will be a few cables and connectors to make up -- but these are pretty straight forward.
Why the delay?
Right now I'm finalizing a couple of small but important details in respect to the backpack design (testing, testing, testing) to ensure that it's as close to a 100% reliable design as is possible to produce.
To this end, I have removed one of the regulators and replaced it with a simpler and more reliable method of reducing the voltage fed to the camera.
Under extensive testing at elevated operating temperatures I found that there original 3-terminal regulator was getting too warm -- so I've ditched it in favour of a charge-pump setup using a diode and capacitor (don't worry -- unless you have a background in electronics your eyes should have glazed over just then).
So, bookmark this page now and come back in a day or so when the final design, bill of materials and other details will be posted.
Discuss this subject in the RCModelReviews Forums
Related links
Fresh Articles:
Join the Forums!

The Blog
Updated: 20 Sep 2012
Here's a blog that will keep you informed just what's going on behind
the scenes at RC Model Reviews and also tells you a little more about
myself.
How compatible are 2.4GHz RC systems?
23 Mar 2010
How come there's no compatibility between different brands of transmitters and receivers?
Why can't you use a cheap Chinese receiver with your Futaba FASST radio?
How to get a product reviewed here
4 Mar 2010
Since this has become a very frequently asked question, I've posted this
simple guide to getting your product, or a product you're thinking of
buying reviewed here at RCModelReviews
How servos work
Useful information on what's inside your servos and how they work.
The Good Oil
Important facts you should know about the oils that are used in our model engine fuels.
Heads-Up: 2.4GHz RC systems tested
How well do five different 2.4GHz systems stack up when hit by interference? The answers are here, with more to come.
Review: Bushnell's $80 Speed Gun
Yes it does work on model airplanes but there are some limitations involved with this bargain-basement radar speed gun.
Review: TowerPro MG995 servo
These are possibly the world's worst servos, find out exactly why you should avoid these boat-anchors at any cost.
Review: SK90

It's cheap but can it really stack up against other glow engines in the .90 market? Find out in this review.
Review: iMax 9X 2.4GHz radio
How does this cheap 9-channel 2.4GHz radio system perform when compared to big-name systems that can cost two or three times as much? Have the Chinese finally developed a real contender with the iMax 9X?
2.4GHz Explained
Does all this 2.4GHz stuff have your head spinning?
I've done my best to demystify the whole subject so if you feel like a bit of learning, this is the stuff for you!
Fix That Engine!
How can you tell when your engine needs new bearings? Who has the best prices and service on replacements? Just how do you change them? Get all that information and watch a great video tutorial anyone can follow.
Chinese Servos - How do they stack up?

The Chinese are now churning out a huge number of very reasonably priced no-name servos. But are they any good?
Baffled by batteries?
Nicad, NiMH, Li-Ion, LiPoly, LiFePO4, A123... the range of different
battery types has never been greater. So how do they differ and
what type should you be using?
Possibly useful: